r: 08096889 p: 2.92 pid: 176274 b: FISCHER q: 10 st: 1 lt: 1 ean: 4048962462203 sr: FISCHER 564595 sr_no_br: 564595 sr_no_br_cl: 564595 sr_cl: FISCHER564595 sr_dash: sold: 4701.2 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 25 mm Overall length 148 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread dimension M16 n: FISCHER 564595 Piercing anchor FAZ II Plus 16/25 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs New ETA confirms the use of FAZ II Plus for the dynamic load of components for diameters M16-M24 under direct load Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 16/25 EV electrolytically galvanised steel kpn: 564595 kpn_dash: kpn_clear: 564595 bkpn: FISCHER 564595 bkpn_clear: FISCHER 564595 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564595 sr_ns: FISCHER564595
r: 87051118 p: 0.92 pid: 75216 b: FISCHER q: 440 st: 1 lt: 1 ean: 4006209409503 sr: FISCHER 40950 sr_no_br: 40950 sr_no_br_cl: 40950 sr_cl: FISCHER40950 sr_dash: sold: 1453.6 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 10/25 mm Overall length 106 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M12 n: FISCHER 40950 rapid-action anchor FBN II 12/10 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 12/10 electrolytically galvanised steel kpn: 40950 kpn_dash: kpn_clear: 40950 bkpn: FISCHER 40950 bkpn_clear: FISCHER 40950 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 40950 sr_ns: FISCHER40950
r: 87051124 p: 2.29 pid: 76269 b: FISCHER q: 300 st: 1 lt: 1 ean: 4006209455647 sr: FISCHER 45564 sr_no_br: 45564 sr_no_br_cl: 45564 sr_cl: FISCHER45564 sr_dash: sold: 1167.9 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 24/40 mm Overall length 145 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M16 n: FISCHER 45564 rapid-action anchor FBN II 16/25 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 16/25 electrolytically galvanised steel kpn: 45564 kpn_dash: kpn_clear: 45564 bkpn: FISCHER 45564 bkpn_clear: FISCHER 45564 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 45564 sr_ns: FISCHER45564
r: 87051004 p: 1.08 pid: 76229 b: FISCHER q: 400 st: 1 lt: 1 ean: 4006209452639 sr: FISCHER 45263 sr_no_br: 45263 sr_no_br_cl: 45263 sr_cl: FISCHER45263 sr_dash: sold: 864 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 30/45 mm Overall length 126 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M12 n: FISCHER 45263 rapid-action anchor FBN II 12/30 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 12/30 electrolytically galvanised steel kpn: 45263 kpn_dash: kpn_clear: 45263 bkpn: FISCHER 45263 bkpn_clear: FISCHER 45263 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 45263 sr_ns: FISCHER45263
r: 02019759 p: 0.55 pid: 16130 b: FISCHER q: 0 st: lt: 8 ean: 4006209441107 sr: FISCHER 44110 sr_no_br: 44110 sr_no_br_cl: 44110 sr_cl: FISCHER44110 sr_dash: sold: 715 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 6 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M6 n: FISCHER 44110 nail anchor FNA II 6x30 M6 with metric thread electrolytically galvanised cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The installation-friendly Hammerset anchor with thread (without nut) for multiple fixings. The fischer nail anchor FNA II 6 with thread (without nut) is made of zinc-plated steel. The FNA II is set in a time-saving manner in the pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II with thread is suitable for fixing metal clamps for conduits and pipes in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Easy removal of fire protection board without damage Reusability of fire protection board Safe anchorage, particularly when exposed to vibration, wind, and pushing/pulling influences Low anchoring depth (30 mm) Convenient installation without torque-controlled setting tool Approved system that has proven itself one million times over Suitable for The washer significantly increases the pulling forces and, at the same time, prevents the damage of the panel during removal Removal by means of easy pinching off of nail head thanks to special 2-stage pliers For fast installation, use the compressed air setting device (item no. 093731) Building materials Concrete C12/15 to C50/60, cracked and non-cracked For multi-point fixings of non-load-bearing systems Application Fire protection plates Fire protection boards Ventilation systems Wire and Nonius hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30 M6 with metric thread electrolytically galvanised kpn: 44110 kpn_dash: kpn_clear: 44110 bkpn: FISCHER 44110 bkpn_clear: FISCHER 44110 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 44110 sr_ns: FISCHER44110
r: 87051141 p: 1.19 pid: 76271 b: FISCHER q: 0 st: lt: 3 ean: 4006209452721 sr: FISCHER 45272 sr_no_br: 45272 sr_no_br_cl: 45272 sr_cl: FISCHER45272 sr_dash: sold: 618.8 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length -/5 mm Overall length 86 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M12 n: FISCHER 45272 rapid-action anchor FBN II 12/5 K electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 12/5 K electrolytically galvanised steel kpn: 45272 kpn_dash: kpn_clear: 45272 bkpn: FISCHER 45272 bkpn_clear: FISCHER 45272 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 45272 sr_ns: FISCHER45272
r: 87051110 p: 0.67 pid: 37426 b: FISCHER q: 0 st: lt: 3 ean: 4006209408278 sr: FISCHER 40827 sr_no_br: 40827 sr_no_br_cl: 40827 sr_cl: FISCHER40827 sr_dash: sold: 502.5 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 10/20 mm Overall length 86 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M10 n: FISCHER 40827 rapid-action anchor FBN II 10/10 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 10/10 electrolytically galvanised steel kpn: 40827 kpn_dash: kpn_clear: 40827 bkpn: FISCHER 40827 bkpn_clear: FISCHER 40827 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 40827 sr_ns: FISCHER40827
r: 87051104 p: 0.5 pid: 74414 b: FISCHER q: 0 st: lt: 1 ean: 4006209406649 sr: FISCHER 40664 sr_no_br: 40664 sr_no_br_cl: 40664 sr_cl: FISCHER40664 sr_dash: sold: 425 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 8 mm Effective length 10/20 mm Overall length 71 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M8 n: FISCHER 40664 rapid-action anchor FBN II 8/10 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 8/10 electrolytically galvanised steel kpn: 40664 kpn_dash: kpn_clear: 40664 bkpn: FISCHER 40664 bkpn_clear: FISCHER 40664 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 40664 sr_ns: FISCHER40664
r: 87051120 p: 1.08 pid: 76266 b: FISCHER q: 0 st: lt: 1 ean: 4006209452646 sr: FISCHER 45264 sr_no_br: 45264 sr_no_br_cl: 45264 sr_cl: FISCHER45264 sr_dash: sold: 410.4 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 50/65 mm Overall length 146 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M12 n: FISCHER 45264 rapid-action anchor FBN II 12/50 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 12/50 electrolytically galvanised steel kpn: 45264 kpn_dash: kpn_clear: 45264 bkpn: FISCHER 45264 bkpn_clear: FISCHER 45264 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 45264 sr_ns: FISCHER45264
r: 87051111 p: 0.81 pid: 75716 b: FISCHER q: 150 st: 1 lt: 1 ean: 4006209408513 sr: FISCHER 40851 sr_no_br: 40851 sr_no_br_cl: 40851 sr_cl: FISCHER40851 sr_dash: sold: 405 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 20/30 mm Overall length 96 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M10 n: FISCHER 40851 rapid-action anchor FBN II 10/20 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 10/20 electrolytically galvanised steel kpn: 40851 kpn_dash: kpn_clear: 40851 bkpn: FISCHER 40851 bkpn_clear: FISCHER 40851 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 40851 sr_ns: FISCHER40851
r: 87051158 p: 7.32 pid: 74280 b: FISCHER q: 20 st: 1 lt: 1 ean: 4006209521922 sr: FISCHER 52192 sr_no_br: 52192 sr_no_br_cl: 52192 sr_cl: FISCHER52192 sr_dash: sold: 366 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 250/265 mm Overall length 370 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M16 n: FISCHER 52192 fastening anchor FBN II 16/250 GS with large washer ev cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing with large washer for flexible use in non-cracked concrete. The fischer bolt anchor FBN II with large washer is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The steel anchor, made of zinc-plated steel and with a large pre-mounted washer, is recommended for fixing bearing beams and sills, as well as other timber constructions. The large washer increases the size of the supporting surface. For the fixing of timber constructions Pre-assembled washer saves time during installation The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility The larger washer included with the FBN II GS creates a large supporting surface and, as such, allows for use in wood construction The pre-fitted washer ensures a fast assembly The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required The anchor is also ideal for large fixture thicknesses The long thread balances component tolerances and stand-off installations, and thus increases flexibility Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture Suitable for The FBN II GS is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Anchor plates with slotted holes Façade sub-structures with slotted holes Timber constructions Tension anchor Anchoring of wooden beams ds: dsc: kts: fastening anchor FBN II 16/250 GS with large washer ev kpn: 52192 kpn_dash: kpn_clear: 52192 bkpn: FISCHER 52192 bkpn_clear: FISCHER 52192 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 52192 sr_ns: FISCHER52192
r: 02137347 p: 5.43 pid: 21108 b: FISCHER q: 0 st: lt: 8 ean: 4048962087482 sr: FISCHER 507565 sr_no_br: 507565 sr_no_br_cl: 507565 sr_cl: FISCHER507565 sr_dash: sold: 325.8 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 30/45 mm Overall length 126 mm Material (bolt) Stainless steel A4 Thread dimension M12 n: FISCHER 507565 rapid-action anchor FBN II 12/30 stainless steel R cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 12/30 stainless steel R kpn: 507565 kpn_dash: kpn_clear: 507565 bkpn: FISCHER 507565 bkpn_clear: FISCHER 507565 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 507565 sr_ns: FISCHER507565
r: 03294160 p: 1.06 pid: 176179 b: FISCHER q: 25 st: 1 lt: 1 ean: 4048962462050 sr: FISCHER 564580 sr_no_br: 564580 sr_no_br_cl: 564580 sr_cl: FISCHER564580 sr_dash: sold: 318 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 20 mm Overall length 105 mm Material (bolt) Steel Surface treatment (bolt) Electrogalvanised Thread dimension M10 n: FISCHER 564580 Piercing anchor FAZ II Plus 10/20 EV electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description For highest demands. Powerful and flexible The fischer bolt anchor FAZ II Plus is the steel anchor for the highest demands with high tensile strengths and a wide range of applications. Heavy loads can be secured in cracked concrete using the steel anchor. The FAZ II Plus is easier and faster to set due to the elimination of drill hole cleaning (M8-M24). The tried-and-tested expansion clip safely introduces the loads into the concrete and enables an immediately loadable, high load-bearing capacity even with dynamic applications. For example, the steel anchor is ideal for the anchoring of railings, cable trays, consoles and for dynamic loads such as lifting platforms, conveyor belts and pumps. Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The new ETA confirms the use of the FAZ II Plus for dynamic loads for diameters M16-M24 The fast installation process of the FAZ II Plus provides an efficient fixing solution for dynamic applications with low load cycles (M16-24) with an immediately loadable fixing point The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The FAZ II Plus allows the absorption of high seismic loads of performance category C1 and C2 for diameters M10-M24 with and without the use of the filling disc FFD at installation The variable anchorage depths allow a millimetre-accurate adjustment to the loads The first bolt anchor M6 with ETA evaluation option 1 ensures a safe and approved anchorage Suitable for The FAZ II Plus is suitable for pre-positioned and push-through installation and is also ideal for stand-off installation thanks to the long thread When applying the torque, the cone bolt is pulled into the expansion sleeve and expands it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved In the case of series installation, we recommend using the FABS or FA-ST II anchor bolt setting tools In case of seismic demands, the annular gap can be filled using the filling disc FFD For dynamic loads, an additional "dynamic set" is used, which is filled with injection mortar (compressive strength >= 50 N/mm² e. g. : FIS V Plus, FIS EM Plus, FIS HB or FIS SB) after installation Building materials Approved for: Concrete C20/25 to C50/60, cracked and non-cracked Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Steel constructions Guard rails Consoles Tunnels Lifts Lifting platforms Conveyor belts Pumps Ladders Cable trays Machines Staircases Façades Timber constructions ds: dsc: kts: Piercing anchor FAZ II Plus 10/20 EV electrolytically galvanised steel kpn: 564580 kpn_dash: kpn_clear: 564580 bkpn: FISCHER 564580 bkpn_clear: FISCHER 564580 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564580 sr_ns: FISCHER564580
r: 87051113 p: 0.88 pid: 76262 b: FISCHER q: 460 st: 1 lt: 1 ean: 4006209408551 sr: FISCHER 40855 sr_no_br: 40855 sr_no_br_cl: 40855 sr_cl: FISCHER40855 sr_dash: sold: 316.8 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 50/60 mm Overall length 126 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M10 n: FISCHER 40855 rapid-action anchor FBN II 10/50 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 10/50 electrolytically galvanised steel kpn: 40855 kpn_dash: kpn_clear: 40855 bkpn: FISCHER 40855 bkpn_clear: FISCHER 40855 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 40855 sr_ns: FISCHER40855
r: 02020027 p: 23.305 pid: 17178 b: FISCHER q: 0 st: lt: 8 ean: 4006209906804 sr: FISCHER 90680 sr_no_br: 90680 sr_no_br_cl: 90680 sr_cl: FISCHER90680 sr_dash: sold: 256.355 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 50 mm Overall length 200 mm n: FISCHER 90680 diamond core drill fastener FDBB 16/50 set cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The reusable fixing system for diamond drills and saws. The fischer fixing set for diamond drills FDBB is suitable for temporary fixing of diamond and core drilling devices as well as diamond saws. The fixing set consists of a reusable spindle bolt with nut and washer. The detachable screw connection between the expansion element and spindle allows for simple dismantling and ensures that the spindle bolt can be reused. The expansion element remains in the drill hole when dismantling the spindle bolt. The spindle bolt is once again completed with an expansion element and can be reused. Detachable screw connection so the fastener can be reused Pre-positioned installation and push-through installation Active controlled expansion behaviour for high levels of safety Robust, reusable spindle bolt The detachable screw connection between the expansion element and spindle enables simple dismantling and ensures that the spindle bolt can be reused The robust, reusable spindle bolt guarantees a long life span The active principle of the anchor bolt enables an active controlled expansion, thus offering a high level of safety The large steel cross-section provides high shear load-bearing capability and, as such, high security for the jerky stoppage of the drill bit Suitable for The FDBB is suitable for pre-positioned and push-through installation An expansion element must be added to the spindle bolt before installation Use a hammer to drive the FDBB through the base plate of the drilling device into the drill hole When the nut is tightened, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The expansion element remains in the drill hole when dismantling the spindle bolt. The spindle bolt is once again completed with an expansion element and can be reused Building materials Suitable for: Concrete C12/15 to C50/60, non-cracked Natural stone with dense structure Application Diamond and core drilling devices Diamond saws ds: dsc: Scope of delivery 1 Spreading element 16 SE 1 Spindle bolt 16/50/160 1 Washer 1 Nut kts: diamond core drill fastener FDBB 16/50 set kpn: 90680 kpn_dash: kpn_clear: 90680 bkpn: FISCHER 90680 bkpn_clear: FISCHER 90680 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 90680 sr_ns: FISCHER90680
r: 02020031 p: 1.18 pid: 17182 b: FISCHER q: 0 st: lt: 8 ean: 4006209906811 sr: FISCHER 90681 sr_no_br: 90681 sr_no_br_cl: 90681 sr_cl: FISCHER90681 sr_dash: sold: 177 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm n: FISCHER 90681 spreader clip FDBB 16 SE cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The expansion element of the fixing system for diamond drills. The fischer fixing set for diamond drills expansion element remains in the drill hole when dismantling the spindle bolt. The spindle bolt is once again completed with an expansion element and can be reused. Pre-positioned installation and push-through installation Active controlled expansion behaviour for high levels of safety Robust, reusable spindle bolt The detachable screw connection between the expansion element and spindle enables simple dismantling and ensures that the spindle bolt can be reused The robust, reusable spindle bolt guarantees a long life span The active principle of the anchor bolt enables an active controlled expansion, thus offering a high level of safety The large steel cross-section provides high shear load-bearing capability and, as such, high security for the jerky stoppage of the drill bit Suitable for The FDBB is suitable for pre-positioned and push-through installation An expansion element must be added to the spindle bolt before installation Use a hammer to drive the FDBB through the base plate of the drilling device into the drill hole When the nut is tightened, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The expansion element remains in the drill hole when dismantling the spindle bolt. The spindle bolt is once again completed with an expansion element and can be reused Building materials Suitable for: Concrete C12/15 to C50/60, non-cracked Natural stone with dense structure Application Diamond and core drilling devices Diamond saws ds: dsc: Scope of delivery (per purchase of 25) 25 x Spreading element kts: spreader clip FDBB 16 SE kpn: 90681 kpn_dash: kpn_clear: 90681 bkpn: FISCHER 90681 bkpn_clear: FISCHER 90681 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 90681 sr_ns: FISCHER90681
r: 87051119 p: 1.26 pid: 75722 b: FISCHER q: 80 st: 1 lt: 1 ean: 4006209445587 sr: FISCHER 44558 sr_no_br: 44558 sr_no_br_cl: 44558 sr_cl: FISCHER44558 sr_dash: sold: 151.2 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 20/35 mm Overall length 116 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M12 n: FISCHER 44558 rapid-action anchor FBN II 12/20 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete The fischer bolt anchor FBN II is a steel anchor for cost-effective fixations in non-cracked concrete. Thanks to its long thread and the two anchorage depths, the fischer bolt anchor FBN II is particularly flexible. In addition to pre-positioned and push-through installation, the bolt anchor is suitable for stand-off installation. In the stainless steel design, the bolt anchor is suitable for façade sub-structures, cantilevers and ladders outside. The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 12/20 electrolytically galvanised steel kpn: 44558 kpn_dash: kpn_clear: 44558 bkpn: FISCHER 44558 bkpn_clear: FISCHER 44558 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 44558 sr_ns: FISCHER44558
r: 08096965 p: 4.29 pid: 176302 b: FISCHER q: 0 st: lt: 8 ean: 4048962463163 sr: FISCHER 564691 sr_no_br: 564691 sr_no_br_cl: 564691 sr_cl: FISCHER564691 sr_dash: sold: 85.8 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 10 mm Effective length 10 mm Overall length 95 mm Material (bolt) Stainless steel Surface treatment (bolt) None Thread dimension M10 n: FISCHER 564691 Piercing anchor FAZ II Plus 10/10 H R stainless steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description With cap nut. For highest demands. Powerful and flexible. The fischer bolt anchor FAZ II Plus H is the steel anchor for highest demands. The new sizes of the special cap nut version (M10 and M12) are also implemented in the ETA assessment and it is ideal for architecturally sophisticated applications. Thanks to variable anchorage depths and easy installation, the FAZ II Plus can be used in many different ways. The tried-and-trusted expansion clip securely feeds the loads into the concrete and ensures a high load-bearing-capacity. The FAZ II Plus H is the optimal solution (for example) for the anchorage of railings in visible areas: The cap nut, not only gives the option for a better and refined optical design but also, ensures an accident free installation due to its closed shape. Quick and easy assembly without the need for drill hole cleaning (M8-M24) Stainless steel: maximum safety for outdoor use Decisive increase in tensile load-bearing capacity due to the new assessment (ETA) - fewer fixing points and smaller anchor plates save time and costs Highest durability over a service life of 120 years is confirmed by the external test certificate of the FAZ II Plus (M10-M16) Highest seismic loads for diameters M10-M24 with and without the use of the filling disc FFD Millimeter accurate adjustment to the loads due to the variable anchoring depths The cap nut is implemented in the ETA assessment and it is ideal for architecturally sophisticated applications Due to its closed shape, the cap nut version ensures an accident free installation The cap nut is implemented in the ETA assessment and it is ideal for architecturally sophisticated applications Due to its closed shape, the cap nut version ensures an accident free installation Quick and easier assembly without the need for drill hole cleaning (M8-M24) Numerous approval certificates for different substrate materials (concrete C12/15-C80/90, steel fiber concrete, solid sand-lime brick) increase the number of applications and fields of use With the new assessment (ETA), the tensile strengths increase decisively. As a result, fewer fixing points and anchors are required The ETA evaluation, together with other test reports (RWS, ZTV, ETK), ensures high loads in case of fire An external independent assessment confirms the service life of anchorages up to 120 years. Thus, the FAZ II Plus outlasts a whole century and is perfectly suited for large, long-lasting construction projects (M10-M16) The variable anchorage depths allow a millimetre-accurate adjustment to the loads Suitable for The FAZ II Plus H is suitable for pre-positioned and push-through installation When applying the torque, the cone bolt is pulled into the expansion sleeve and expand it against the drill hole wall The anchor is set in line with the approval once the preset installation torque is achieved Building materials Approved for: Beton C20/25 bis C50/60, gerissen und ungerissen Also suitable for: Concrete C12/15 (classification available) Concrete C80/95 (classification available) Steel fiber concrete (classification available) Solid sand-lime brick (classification available) Application Guard rails Consoles ds: dsc: kts: Piercing anchor FAZ II Plus 10/10 H R stainless steel kpn: 564691 kpn_dash: kpn_clear: 564691 bkpn: FISCHER 564691 bkpn_clear: FISCHER 564691 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 564691 sr_ns: FISCHER564691
r: 87051159 p: 7.88 pid: 75745 b: FISCHER q: 0 st: lt: 8 ean: 4006209522042 sr: FISCHER 52204 sr_no_br: 52204 sr_no_br_cl: 52204 sr_cl: FISCHER52204 sr_dash: sold: 78.8 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 16 mm Effective length 300/315 mm Overall length 420 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M16 n: FISCHER 52204 fastening anchor FBN II 16/300 GS with large washer ev cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing with large washer for flexible use in non-cracked concrete. The fischer bolt anchor FBN II with large washer is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The steel anchor, made of zinc-plated steel and with a large pre-mounted washer, is recommended for fixing bearing beams and sills, as well as other timber constructions. The large washer increases the size of the supporting surface. For the fixing of timber constructions Pre-assembled washer saves time during installation The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility The larger washer included with the FBN II GS creates a large supporting surface and, as such, allows for use in wood construction The pre-fitted washer ensures a fast assembly The standard anchorage depth achieves the maximum load-bearing capacities. This means that fewer fixing points and smaller anchor plates are required The anchor is also ideal for large fixture thicknesses The long thread balances component tolerances and stand-off installations, and thus increases flexibility Fewer hammer blows and the minimal torque slippage allow for a noticeably simpler assembly The drive-in pin protects the threaded screw from damage, and as such ensures a faster installation and dismantling of the fixture Suitable for The FBN II GS is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Anchor plates with slotted holes Façade sub-structures with slotted holes Timber constructions Tension anchor Anchoring of wooden beams ds: dsc: kts: fastening anchor FBN II 16/300 GS with large washer ev kpn: 52204 kpn_dash: kpn_clear: 52204 bkpn: FISCHER 52204 bkpn_clear: FISCHER 52204 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 52204 sr_ns: FISCHER52204
r: 02137181 p: 2.84 pid: 21043 b: FISCHER q: 0 st: lt: 8 ean: 4006209452691 sr: FISCHER 45269 sr_no_br: 45269 sr_no_br_cl: 45269 sr_cl: FISCHER45269 sr_dash: sold: 56.8 p_range: none type: standard act: 1 avo: 1 av: Drilling diameter 12 mm Effective length 160/175 mm Overall length 256 mm Material (bolt) Steel Surface treatment (bolt) Zinc plated Thread dimension M12 n: FISCHER 45269 rapid-action anchor FBN II 12/160 electrolytically galvanised steel cn: ANCHOR BOLT cn2: ANCHOR BOLT cn_clear: ANCHORBOLT d: Product description The cost-efficient fixing for flexible use in non-cracked concrete. The fischer bolt anchor FBN II is a steel anchor for cost-effective fixings in non-cracked concrete. Due to the long thread and the two anchorage depths, the fischer bolt anchor FBN II can be used in a particularly flexible manner. The bolt anchor is also suitable for stand-off installation as well as pre-positioned and in push-through installation. The zinc-plated steel version of the bolt anchor is suitable for fixing railings, cable trays, and consoles in internal areas. The FBN II achieves maximum load-bearing capacity with standard anchorage depth. This means: fewer fixing points and smaller anchor plates If the reduced anchorage depth is used, then this lowers the drill hole depth and simplifies installation Component tolerances are balanced out with the long thread. In addition, FBN II is also suitable for stand-off installations. This increases flexibility Simple assembly due to few taps and minimal slippage The drive-in pin protects the thread from damage. This saves time during installation and removal The standard anchorage depth achieves the maximum load-bearing capacities. Thus fewer fixing points and smaller anchor plates are required The reduced anchorage depth reduces the drill hole depth. This minimises the amount of time needed for installation whilst increasing flexibility The long thread balances component tolerances and allows for stand-off installations, thus increasing flexibility Few hammer blows and the minimal torque slippage allow for a noticeably simpler installation The drive-in pin protects the thread from damage, and thus ensures a faster installation and dismantling of the attachment Suitable for The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut) When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall The head embossing offers a simple control of the anchoring In the case of series installation, we recommend using the FABS bolt anchor setting tool Building materials Approved for: Concrete C20/25 to C50/60, non-cracked Also suitable for: Concrete C12/15 Natural stone with dense structure Application Steel constructions Guard rails Consoles Ladders Cable trays Machines Staircases Gates Façades ds: dsc: kts: rapid-action anchor FBN II 12/160 electrolytically galvanised steel kpn: 45269 kpn_dash: kpn_clear: 45269 bkpn: FISCHER 45269 bkpn_clear: FISCHER 45269 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Anchor bolt | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer anchor bolt sr_no_br_cl_ns: 45269 sr_ns: FISCHER45269
