r: 02019788 p: 1.06 pid: 17171 b: FISCHER q: 0 st: lt: 8 ean: 4006209441183 sr: FISCHER 44118 sr_no_br: 44118 sr_no_br_cl: 44118 sr_cl: FISCHER44118 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 110 mm Effective length 75 mm Head diameter 13 mm Drilling diameter 6 mm n: FISCHER 44118 nail anchor FNA II 6x30/75 with nail head electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor for multiple fixings. The fischer nail anchor FNA II 6 with nail head is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing fire protection boards, wire and nonious hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Series installation possible with setting tool for the hammer drill. This saves time and costs The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and pushthrough installation. The FNA II OE and Hare suitable for pre-positioned installation The installed nail anchor FNA II expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and nonious hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30/75 with nail head electrolytically galvanised kpn: 44118 kpn_dash: kpn_clear: 44118 bkpn: FISCHER 44118 bkpn_clear: FISCHER 44118 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44118 sr_ns: FISCHER44118
r: 02908417 p: 0.82 pid: 176100 b: FISCHER q: 0 st: lt: 8 ean: 4048962323467 sr: FISCHER 545637 sr_no_br: 545637 sr_no_br_cl: 545637 sr_cl: FISCHER545637 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Drilling diameter 6 mm n: FISCHER 545637 ceiling anchor FDN II 6/35 cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly push-through anchor for multiple fixings. The fischer ceiling nail FDN II is a zinc-plated steel push-through anchor. The FDN II is approved for multiple anchorings of non-structural systems in concrete. The fischer ceiling nail FDN II is ideal for anchoring wire and nonious hangers for suspended ceilings, ventilation systems, and metal profiles in cracked concrete. The European Technical Approval and classification as per fire resistance class R 120 ensure added safety. The ceiling nail is installed time-saving using a push-through installation and is hammered into the drill hole. The simple active principle allows for cost-efficient hammerset installation The two hit zones ensure correct installation The head embossing offers a simple control of the anchoring, and thus saves time The simple active principle allows for cost-efficient hammerset installation The new short version FDN II K with reduced anchorage depth ist faster to install and reduces reinforcement hits The flush-sunk expansion nail signifies the complete expansion of the anchor, and thereby ensures minimum movement when under load The fischer FDN II can be installed without cleaning of the drill hole The head embossing offers a simple control of the anchoring, and thus saves time Suitable for The FDN II is suitable for push-through installation The FDN II ceiling nail is driven into the drill hole with a hammer until it is firmly in position. Do not hit the expansion wedge at this stage Then, drive the expansion wedge in flush to the nail head. This causes the FDN II to expand against the drill hole wall Building materials Approved for: Oncrete C12/15 to C50/60 Concrete C20/25 to C50/60, cracked, for the multiple fixings of non-load-bearing systems Also suitable for: Natural stone with dense structure Application Wire and Nonius hangers Ventilation systems Slats Metal profiles Perforated tapes Sub-structures made of metal ds: dsc: kts: ceiling anchor FDN II 6/35 kpn: 545637 kpn_dash: kpn_clear: 545637 bkpn: FISCHER 545637 bkpn_clear: FISCHER 545637 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 545637 sr_ns: FISCHER545637
r: 02019787 p: 0.81 pid: 15983 b: FISCHER q: 0 st: lt: 8 ean: 4006209441176 sr: FISCHER 44117 sr_no_br: 44117 sr_no_br_cl: 44117 sr_cl: FISCHER44117 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 85 mm Effective length 50 mm Head diameter 13 mm Drilling diameter 6 mm n: FISCHER 44117 nail anchor FNA II 6x30/50 with nail head electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor for multiple fixings. The fischer nail anchor FNA II 6 with nail head is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing fire protection boards, wire and nonious hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Series installation possible with setting tool for the hammer drill. This saves time and costs The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and pushthrough installation. The FNA II OE and Hare suitable for pre-positioned installation The installed nail anchor FNA II expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and nonious hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30/50 with nail head electrolytically galvanised kpn: 44117 kpn_dash: kpn_clear: 44117 bkpn: FISCHER 44117 bkpn_clear: FISCHER 44117 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44117 sr_ns: FISCHER44117
r: 02019786 p: 0.74 pid: 17167 b: FISCHER q: 0 st: lt: 8 ean: 4006209441169 sr: FISCHER 44116 sr_no_br: 44116 sr_no_br_cl: 44116 sr_cl: FISCHER44116 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 65 mm Effective length 30 mm Head diameter 13 mm Drilling diameter 6 mm n: FISCHER 44116 nail anchor FNA II 6x30/30 with nail head electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor for multiple fixings. The fischer nail anchor FNA II 6 with nail head is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing fire protection boards, wire and nonious hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Series installation possible with setting tool for the hammer drill. This saves time and costs The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and pushthrough installation. The FNA II OE and Hare suitable for pre-positioned installation The installed nail anchor FNA II expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and nonious hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30/30 with nail head electrolytically galvanised kpn: 44116 kpn_dash: kpn_clear: 44116 bkpn: FISCHER 44116 bkpn_clear: FISCHER 44116 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44116 sr_ns: FISCHER44116
r: 02019859 p: 0.73 pid: 17440 b: FISCHER q: 0 st: lt: 8 ean: 4006209441275 sr: FISCHER 44127 sr_no_br: 44127 sr_no_br_cl: 44127 sr_cl: FISCHER44127 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 54 mm Drilling diameter 6 mm n: FISCHER 44127 nail anchor FNA II 6x25 oe with eye electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor with eye for multiple fixings. The fischer nail anchor FNA II 6 with eye is made of zinc-plated steel. The FNA II is set in a time-saving manner in the pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with eye is suitable for fixing air lines and hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold With eye The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and push-through installation. The FNA II OE and H are suitable for pre-positioned installation The installed FNA II nail anchor expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and Nonius hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x25 oe with eye electrolytically galvanised kpn: 44127 kpn_dash: kpn_clear: 44127 bkpn: FISCHER 44127 bkpn_clear: FISCHER 44127 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44127 sr_ns: FISCHER44127
r: 02019857 p: 0.73 pid: 15986 b: FISCHER q: 0 st: lt: 8 ean: 4006209441268 sr: FISCHER 44126 sr_no_br: 44126 sr_no_br_cl: 44126 sr_cl: FISCHER44126 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 54 mm Drilling diameter 6 mm n: FISCHER 44126 nail anchor FNA II 6x25 H with hook electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor with hook for multiple fixings. The fischer nail anchor FNA II 6 with hook is made of zinc-plated steel. The FNA II is set in a time-saving manner in the pre-positioned installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with hook is suitable for fixing air lines and hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold With hook The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and push-through installation. The FNA II OE and H are suitable for pre-positioned installation The installed FNA II nail anchor expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and Nonius hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x25 H with hook electrolytically galvanised kpn: 44126 kpn_dash: kpn_clear: 44126 bkpn: FISCHER 44126 bkpn_clear: FISCHER 44126 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44126 sr_ns: FISCHER44126
r: 02019784 p: 0.58 pid: 17419 b: FISCHER q: 0 st: lt: 8 ean: 4006209441152 sr: FISCHER 44115 sr_no_br: 44115 sr_no_br_cl: 44115 sr_cl: FISCHER44115 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 40 mm Effective length 5 mm Head diameter 13 mm Drilling diameter 6 mm n: FISCHER 44115 nail anchor FNA II 6x30/5 with nail head electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor for multiple fixings. The fischer nail anchor FNA II 6 with nail head is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing fire protection boards, wire and nonious hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Series installation possible with setting tool for the hammer drill. This saves time and costs The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and pushthrough installation. The FNA II OE and Hare suitable for pre-positioned installation The installed nail anchor FNA II expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and nonious hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x30/5 with nail head electrolytically galvanised kpn: 44115 kpn_dash: kpn_clear: 44115 bkpn: FISCHER 44115 bkpn_clear: FISCHER 44115 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44115 sr_ns: FISCHER44115
r: 02019793 p: 0.5 pid: 17174 b: FISCHER q: 0 st: lt: 8 ean: 4006209441213 sr: FISCHER 44121 sr_no_br: 44121 sr_no_br_cl: 44121 sr_cl: FISCHER44121 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Length 35 mm Effective length 5 mm Head diameter 13 mm Drilling diameter 6 mm n: FISCHER 44121 nail anchor FNA II 6x25/5 with nail head electrolytically galvanised cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly Hammerset anchor for multiple fixings. The fischer nail anchor FNA II 6 with nail head is made of zinc-plated steel. The FNA II is set in a time-saving manner in the push-through installation with just a few taps of the hammer. The installed FNA II expands automatically under load. The cone is then pulled into the expansion clip and expands it against the hole wall. Above all, the fischer nail anchor FNA II 6 with nail head is suitable for fixing fire protection boards, wire and nonious hangers in internal areas. Hammerset installation saves time No reinforcement hits due to low anchorage depth This saves time and costs during series installation Expansion clip provides a firm hold ETA approval for multiple fixings Series installation possible with setting tool for the hammer drill. This saves time and costs The special active principle allows for a simple hammerset installation and, therefore, a short processing time The extremely short anchor depth prevents reinforcement hits, and creates the conditions for a trouble-free installation The optimised expansion clip ensures hold when placing in the drill hole, and prevents it falling out during overhead installations The massive shaft cross-section guarantees a high load-bearing capacity, thus offering an extremely high level of safety A range of head shapes allows for the fixing of wide-ranging fixtures, and for the ideal adaptation to suit the intended use Suitable for The FNA II with nail head is suitable for push-through installation. The FNA II M6 is suitable for pre-positioned and pushthrough installation. The FNA II OE and Hare suitable for pre-positioned installation The installed nail anchor FNA II expands automatically under load. The cone is pulled into the expansion clip and expands it against the drill hole wall Available setting tools:FNA S-SBO to slip onto the drill,FNA S-SDS for series installation with a drilling hammer,FNA S-H for the manual installation of mounting rails Building materials Approved for: Concrete C12/15 to C50/60, cracked, for multiple fixings of non-structural applications Also suitable for: Solid sand-lime brick Natural stone with dense structure Prestressed hollow-core concrete slabs Application Fire protection plates Fire protection boards Ventilation systems Wire and nonious hangers Mounting rails Metal clamps Substructures made of wood and metal ds: dsc: kts: nail anchor FNA II 6x25/5 with nail head electrolytically galvanised kpn: 44121 kpn_dash: kpn_clear: 44121 bkpn: FISCHER 44121 bkpn_clear: FISCHER 44121 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 44121 sr_ns: FISCHER44121
r: 02908409 p: 0.35 pid: 176094 b: FISCHER q: 0 st: lt: 8 ean: 4048962323450 sr: FISCHER 545636 sr_no_br: 545636 sr_no_br_cl: 545636 sr_cl: FISCHER545636 sr_dash: sold: 0 p_range: none type: standard act: 1 avo: 1 av: Material Steel Surface treatment Zinc plated Drilling diameter 6 mm n: FISCHER 545636 ceiling anchor FDN II 6/5 cn: DROP-IN ANCHOR cn2: DROP-IN ANCHOR cn_clear: DROPINANCHOR d: Product description The installation-friendly push-through anchor for multiple fixings. The fischer ceiling nail FDN II is a zinc-plated steel push-through anchor. The FDN II is approved for multiple anchorings of non-structural systems in concrete. The fischer ceiling nail FDN II is ideal for anchoring wire and nonious hangers for suspended ceilings, ventilation systems, and metal profiles in cracked concrete. The European Technical Approval and classification as per fire resistance class R 120 ensure added safety. The ceiling nail is installed time-saving using a push-through installation and is hammered into the drill hole. The simple active principle allows for cost-efficient hammerset installation The two hit zones ensure correct installation The head embossing offers a simple control of the anchoring, and thus saves time The simple active principle allows for cost-efficient hammerset installation The new short version FDN II K with reduced anchorage depth ist faster to install and reduces reinforcement hits The flush-sunk expansion nail signifies the complete expansion of the anchor, and thereby ensures minimum movement when under load The fischer FDN II can be installed without cleaning of the drill hole The head embossing offers a simple control of the anchoring, and thus saves time Suitable for The FDN II is suitable for push-through installation The FDN II ceiling nail is driven into the drill hole with a hammer until it is firmly in position. Do not hit the expansion wedge at this stage Then, drive the expansion wedge in flush to the nail head. This causes the FDN II to expand against the drill hole wall Building materials Approved for: Oncrete C12/15 to C50/60 Concrete C20/25 to C50/60, cracked, for the multiple fixings of non-load-bearing systems Also suitable for: Natural stone with dense structure Application Wire and Nonius hangers Ventilation systems Slats Metal profiles Perforated tapes Sub-structures made of metal ds: dsc: kts: ceiling anchor FDN II 6/5 kpn: 545636 kpn_dash: kpn_clear: 545636 bkpn: FISCHER 545636 bkpn_clear: FISCHER 545636 c_path: Home / Fasteners and machine components / Fasteners / Anchoring / Drop-in anchor | Home / Our brands / Fischer / Fischer fasteners and machine components / Fischer fasteners / Fischer anchoring / Fischer drop-in anchor sr_no_br_cl_ns: 545636 sr_ns: FISCHER545636
